Magnum One

home *** CD-ROM | disk | FTP | other *** search

/ Magnum One / Magnum One (Mid-American Digital) (Disc Manufacturing).iso / d8 / telix_dv.doc < prev next >

Wrap

Text File | 1991-08-04 | 13.2 KB | 214 lines

Telix 3.12 (trademark) under DESKVIEW (trademark). by: Lawrence E. Widacki If you are using a mouse on COM1 and your modem board is on COM3 then you MUST set the modem board to IRQ2 or IRQ5. I use COM3 - IRQ2 with no problems. Same is true is mouse is on COM2 and modem board is on COM4. Some BUS mice trap IRQ2 so you mite use IRQ5 for the modem board. If you have LPT2 then IRQ5 may not be available. Check your manuals, for the information is usually there. These IRQ's may not have any conflic under just DOS, but they will have conflic under DESKVIEW. This is the configuration I use with Telix 3.12, a mouse on COM1, and the modem board on COM3 - IRQ2. This works with DESKVIEW so long you setup DESKVIEW the same way I show below Telix 3.12 configuration. Save your Telix 3.12 configuration by copying TELIX.CNF to another file incase you have problems. If you set the modem board to a new configuration before you reconfigure Telix, Telix 3.12 will HANG UP at the modem intialization point, because it will never recieve the OK from the modem. This may not be a bug, but worth mentioning it. To avoid this, reconfigure Telix 3.12 first then reconfigure the modem board, else, using a text editor, edit TELIX.CNF. Search for `c3irq=' and change the number to the IRQ you will be using. Also search for `port=' and make sure the COM port number your using is correct. DOUBLE CHECK YOUR SETTINGS IF YOU HAVE PROBLEMS. ╒═╡ Configure Telix ╞════════════╕ │ │ │ Change which default settings? │ │ │ │ Screen and color │ select ------> │ Terminal options │ │ General options │ │ Modem and dialing │ │ Filenames and paths │ │ Ascii transfers │ │ Protocol options │ │ Kermit transfers │ │ Comm port setup │ │ Write setup to disk │ │ Exit │ │ │ ╘════════════════════════════════╛ /------ MAKE SURE THIS IS CORRECTLY SET TO YOUR COM PORT ----- | | ╒═╡ Terminal options ╞═══════════════════════════════════════════════════╕ | │ │ | │ A - Baud 2400 Parity None Data length 8 Stop bits 1 │ \-->│ B - COM3 │ │ │ │ C - Default terminal type ........... ANSI-BBS │ │ D - Status line ..................... Bottom │ │ E - Local echo ...................... Off │ │ F - Add Line Feeds after CRs ........ Off │ │ G - Strip high bit (incoming data) .. Off │ │ H - Received Backspace destructive .. On │ │ I - Backspace key sends ............. BS │ │ J - XON/XOFF software flow control .. On │ │ K - CTS/RTS hardware flow control ... Off │ │ L - DSR/DTR hardware flow control ... On │ │ M - Compuserve Quick B transfers .... On │ │ N - Zmodem auto-downloads ........... On │ │ O - Answerback string (ENQ) ......... │ │ │ │ │ │ Change which setting? (Return or Esc to exit) │ ╘════════════════════════════════════════════════════════════════════════╛ ╒═╡ Configure Telix ╞════════════╕ │ │ │ Change which default settings? │ │ │ │ Screen and color │ │ Terminal options │ │ General options │ │ Modem and dialing │ │ Filenames and paths │ │ Ascii transfers │ │ Protocol options │ │ Kermit transfers │ select ------> │ Comm port setup │ │ Write setup to disk │ │ Exit │ │ │ ╘════════════════════════════════╛ /---- MAKE SURE THIS IS CORRECT ---\ | | | | | ╒═╡ Comm port setup ╞═════════════════════════════════╕ | │ │ | │ Start IRQ │ | │ Address Line │ | THE │ │ | COM │ A: COM1 ..... 3f8 4 │ | PORT │ / │ | I │ B: COM2 ..... 2f8 3 | THE │ | USE │ | IRQ │ \-------->│ C: COM3 ..... 3e8 2 <-----{ I │ │ | USE │ │ D: COM4 ..... 2e8 3 | │ │ \ │ │ E: COM5 ..... 3f8 4 │ │ │ │ F: COM6 ..... 3f8 4 │ │ │ │ G: COM7 ..... 3f8 4 │ │ │ │ H: COM8 ..... 3f8 4 │ │ │ │ Change which setting? (Return or Esc to exit) │ ╘═════════════════════════════════════════════════════╛ ╒═╡ Configure Telix ╞════════════╕ │ │ │ Change which default settings? │ │ │ │ Screen and color │ │ Terminal options │ │ General options │ SAVE │ Modem and dialing │ YOUR │ Filenames and paths │ SETTINGS │ Ascii transfers │ │ Protocol options │ │ Kermit transfers │ │ Comm port setup │ select ------> │ Write setup to disk │ │ Exit │ │ │ ╘════════════════════════════════╛ Configuration for DESKVIEW. Just follow these settings. Set PROGRAM and DIRECTORY to your directories. 1══Change═a═Program═══════════════════════════════════════════════════════════╗ ║ Change a Program ║ ║ ║ ║ Program Name............: Telix ║ ║ ║ ║ Keys to Use on Open Menu: TX Memory Size (in K): 300 ║ ║──────────────────────────────────────────────────────────────────────────────║ ║ Program...: c:\telix\telix ║ ║ ║ ║ Parameters: ║ ║ ║ ║ Directory.: c:\telix ║ ║──────────────────────────────────────────────────────────────────────────────║ ║ Options: ║ ║ Writes text directly to screen.......: [Y] ║ ║ Displays graphics information........: [N] ║ ║ Virtualize text/graphics (Y,N,T).....: [Y] ║ ║ Uses serial ports (Y,N,1,2)..........: [N] ║ ║ Requires floppy diskette.............: [N] ║ ║ ║ ║ Press F1 for advanced options Press ─┘ when you are DONE ║ ╚══════════════════════════════════════════════════════════════════════════════╝ Press F1 for advance options and follow these settings. These settings should be set exactly the way I show. 1══Change═a═Program═══════════════════════════════════════════════════════════╗ ║ Change a Program Advanced Options ║ ║ ║ ║ System Memory (in K).......: 0 Maximum Program Memory Size (in K)..: ║ ║ ║ ║ Script Buffer Size.......: 1000 Maximum Expanded Memory Size (in K): ║ ║ ║ ║ Text Pages: 1 Graphics Pages: 0 Initial Mode: Interrupts: 00 to FF ║ ║──────────────────────────────────────────────────────────────────────────────║ ║ Window Position: ║ ║ Maximum Height: 25 Starting Height: Starting Row...: ║ ║ Maximum Width.: 80 Starting Width.: Starting Column: ║ ║──────────────────────────────────────────────────────────────────────────────║ ║ Shared Program ║ ║ Pathname..: ║ ║ Data......: ║ ║──────────────────────────────────────────────────────────────────────────────║ ║ Close on exit (Y,N,blank)......: [Y] Uses its own colors..............: [Y] ║ ║ Allow Close Window command.....: [N] Runs in background (Y,N,blank)...: [Y] ║ ║ Uses math coprocessor..........: [N] Keyboard conflict (0-F)..........: [0] ║ ║ Share CPU when foreground......: [Y] Share EGA when foreground/zoomed.: [N] ║ ║ Can be swapped out (Y,N,blank).: [N] Protection level (0-3)...........: [0] ║ ║ ║ ║ Press F1 for standard options Press ─┘ when you are DONE ║ ╚══════════════════════════════════════════════════════════════════════════════╝ If you want to run Telix 3.12 in 43/80 mode then change Maximun Height to 43. If you want to run Telix 3.12 in 50/80 mode then change Maximun Height to 50. These changes will make Telix 3.12 start in the correct mode based on the maximun height. No need of special prameters.